Hammers SilverSchmidt for testing concrete
The SilverSchmidt ST/PC is the first integrated concrete test hammer featuring true rebound value and unmatched repeatability.
Two factors contribute to the improved performance of the SilverSchmidt ST/PC over its predecessors:
• Velocity based detection of the rebound quotient
• The lightweight hybrid design of the impact plunger is made from aerospace alloy, matched to the elastic properties of the concrete and equipped with a hardness steel cap
Independent validation testing by BAM (Federal Institute for Materials Research and Testing, Germany) has shown the SilverSchmidt ST/PC to have less dispersion than the classical concrete test hammer over the entire range.
The unique design and high quality construction of the concrete test hammer SilverSchmidt ST/PC makes rebound hammer testing quicker and more accurate than ever before.
Features
- The SilverSchmidt ST/PC concrete test hammer combines a high measurement accuracy with an unmatched repeatability.
- Impact direction independence: The forward and the rebound velocity of the hammer mass are both measured in close proximity to the point of impact. The rebound value requires no angular correction
- Customer conversion curves for a wide range of compressive concrete strengths, including low fc (<10 N/mm2, 1’450 psi) and high strength concrete (up to 100 N/mm2, 14’500 psi)
- Objective evaluation: a large number of measurement points can be easily collected by the SilverSchmidt ST/PC and automatically evaluated according to statistical data
- A two-layer seal prevents dust and dirt from penetrating the interior of the concrete test hammer.
- Ergonomics: the SilverSchmidt ST/PC body lies very comfortable in the hand
- Automatic conversion to the required measurement unit (MPa, N/mm2, kg/cm2, psi)
Applications
- Ideally suited for on-site tests of concrete
- Suitable for testing a wide variety of concrete, mortar and rock
- Handy for difficult to access or confined test areas (i.e. working overhead)
- Especially convenient for tests on tunnel linings as measurements with the SilverSchmidt ST/PC are independent of impact direction
- Assessment on young, soft concrete with mushroom plunger (e.g. to indicate when to remove forms or for formwork)
Product Variations
- concrete test hammer SilverSchmidt Type ST N - Standard impact energy (2.207 Nm)
- concrete test hammer SilverSchmidt Type ST L - Reduced impact energy (0.735 Nm)
- concrete test hammer SilverSchmidt Type PC N - Standard impact energy (2.207 Nm) with PC communication, increased memory capacity and Hammerlink software
- concrete test hammer SilverSchmidt Type PC L- Reduced impact energy (0.735 Nm) with PC communication, increased memory capacity and Hammerlink software
Warranties
- Standard 2-year limited warranty on electronic parts
- Optional extended warranty periods up to 3 additional years
Applicable Standards
- EN12504-2 (European Standard)
- ASTM C 805 (North American Standard)
- JGJ/T 23-2001 (Chinese Standard)
Technical Data
Mechanical data | Type ST N / PC N |
Type ST L / PC L |
Impact energy | 2.207 Nm |
0.735 Nm |
Hammer mass | 135 g |
135 g |
Spring constant | 0.79 N/mm |
0.26 N/mm |
Spring extension | 75 mm (2.95”) |
75 mm (2.95”) |
Housing dimensions | 55 x 55 x 255 mm (2.16” x 2.16” x 9.84”) |
|
Weight | 570 g (1.3 lb) | |
PC application | ||
Only for the concrete test hammer SilverSchmidt versions PC N and PC L: Hammerlink Software | ||
Electrical data | ||
Display | 17 x 71 pixels; graphic / alphanumeric | |
Power consumption | ~13 mA measuring, ~4 mA setup and review, ~0.02 mA idle | |
Battery life | >5000 impacts (before recharging) | |
Charger connection | USB type B (5V, 100 mA) | |
Measuring ranges | ||
Concrete compressive strength | 10-100 N/mm2 (1450-14500 psi) | |
Operating temperature | 0 to 50 °C (32 to 122 °F) | |
Storage temperature | -10 to 70 °C (14 to 158 °F) |
More Information
www.silverschmidt.com
< Prev | Next > |
---|